很長一段時間，nand flash都是嵌入式的標配產品。nand flash價格便宜，存儲量大，適用于很多的場景?，F(xiàn)在很普及的ssd，上面的存儲模塊其實也是由一塊一塊nand flash構成的。對于linux嵌入式來說，開始uboot的加載是硬件完成的，中期的kernel加載是由uboot中的nand flash驅動完成的，而后期的rootfs加載，這就要靠kernel自己來完成了。當然，這次還是以三星s3c芯片為例進行說明。
1、nand flash驅動在什么地方，可以從drviers/mtd/Makefile來看
|
1
|
obj-y += chips/ lpddr/ maps/ devices/ nand/ onenand/ tests/ |
2、nand在mtd下面，是作為一個單獨目錄保存的，這時應該查看nand下的Kconfig
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
|
config MTD_NAND_S3C2410 tristate "NAND Flash support for Samsung S3C SoCs" depends on ARCH_S3C24XX || ARCH_S3C64XX help This enables the NAND flash controller on the S3C24xx and S3C64xx SoCs No board specific support is done by this driver, each board must advertise a platform_device for the driver to attach. config MTD_NAND_S3C2410_DEBUG bool "Samsung S3C NAND driver debug" depends on MTD_NAND_S3C2410 help Enable debugging of the S3C NAND driver config MTD_NAND_S3C2410_CLKSTOP bool "Samsung S3C NAND IDLE clock stop" depends on MTD_NAND_S3C2410 default n help Stop the clock to the NAND controller when there is no chip selected to save power. This will mean there is a small delay when the is NAND chip selected or released, but will save approximately 5mA of power when there is nothing happening. |
3、不難發現，MTD_NAND_S3C2410才是那個真正的macro，嘗試在Makefile找文件
|
1
|
obj-$(CONFIG_MTD_NAND_S3C2410) += s3c2410.o |
4、查看s3c2410.c文件，看看基本結構構成
|
1
2
3
4
5
6
7
8
9
10
11
12
13
|
static struct platform_driver s3c24xx_nand_driver = { .probe = s3c24xx_nand_probe, .remove = s3c24xx_nand_remove, .suspend = s3c24xx_nand_suspend, .resume = s3c24xx_nand_resume, .id_table = s3c24xx_driver_ids, .driver = { .name = "s3c24xx-nand", .of_match_table = s3c24xx_nand_dt_ids, }, }; module_platform_driver(s3c24xx_nand_driver); |
5、繼續分析s3c24xx_nand_probe函數
|
1
|
s3c2410_nand_init_chip(info, nmtd, sets); |
6、之所以從中摘出了s3c2410_nand_init_chip這個函數，是因為里面進行了函數注冊
類似的函數還有s3c2410_nand_update_chip函數
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
|
chip->write_buf = s3c2410_nand_write_buf; chip->read_buf = s3c2410_nand_read_buf; chip->select_chip = s3c2410_nand_select_chip; chip->chip_delay = 50; nand_set_controller_data(chip, nmtd); chip->options = set->options; chip->controller = &info->controller; switch (info->cpu_type) { case TYPE_S3C2410: chip->IO_ADDR_W = regs + S3C2410_NFDATA; info->sel_reg = regs + S3C2410_NFCONF; info->sel_bit = S3C2410_NFCONF_nFCE; chip->cmd_ctrl = s3c2410_nand_hwcontrol; chip->dev_ready = s3c2410_nand_devready; break; case TYPE_S3C2440: chip->IO_ADDR_W = regs + S3C2440_NFDATA; info->sel_reg = regs + S3C2440_NFCONT; info->sel_bit = S3C2440_NFCONT_nFCE; chip->cmd_ctrl = s3c2440_nand_hwcontrol; chip->dev_ready = s3c2440_nand_devready; chip->read_buf = s3c2440_nand_read_buf; chip->write_buf = s3c2440_nand_write_buf; break; case TYPE_S3C2412: chip->IO_ADDR_W = regs + S3C2440_NFDATA; info->sel_reg = regs + S3C2440_NFCONT; info->sel_bit = S3C2412_NFCONT_nFCE0; chip->cmd_ctrl = s3c2440_nand_hwcontrol; chip->dev_ready = s3c2412_nand_devready; if (readl(regs + S3C2410_NFCONF) & S3C2412_NFCONF_NANDBOOT) dev_info(info->device, "System booted from NAND\n"); break; } |
7、抓住了函數接口，就找到了基本邏輯。
對于框架來說，它不關心你的代碼如何實現。只要你按照它的接口寫，就能讓上層正常獲得數據。platform、usb、pci這都是一種接口形式，具體實現還要按照各個具體功能模塊來實現才行。
8、為什么我們都用s3c芯片進行舉例
因為它用的場景最多，學習資料最全，對于新手來說，這會少很多麻煩。
9、這個驅動依賴的kernel版本是什么
這里最有的代碼都是按照最新4.16的版本進行分析的，大家可以直接查看這里的地址。
以上就是本文的全部內容，希望對大家的學習有所幫助，也希望大家多多支持服務器之家。
原文鏈接：https://blog.csdn.net/feixiaoxing/article/details/79855970
